会员登录|免费注册|忘记密码|管理入口 返回主站||保存桌面|手机浏览|联系方式|购物车
企业会员(开通需19.9元/月)第1年

广东多正化工科技有限公司  

无三苯环保PU胶,接枝胶,万能胶,装修胶,处理剂,生粉胶,喷胶,贴合胶,固化剂、清洁剂、中底胶,沙发喷胶,箱包、手袋专用胶,篮球胶,塑道跑道胶,单程坐垫胶等等,共计100多个品种。

搜索
新闻中心
产品分类
  • 暂无分类
联系方式
  • 联系人:梁建锋
  • 电话:0757-85768283
  • 邮件:gddzhg@126.com
  • 传真:0757-85738282
站内搜索
 
荣誉资质
  • 暂未上传
友情链接
  • 暂无链接
首页 > 供应产品 > 水性喷胶产品中英文介绍 汽车内饰无味水性喷胶 出口水性喷胶
水性喷胶产品中英文介绍 汽车内饰无味水性喷胶 出口水性喷胶
单价 面议对比
询价 暂无
发货 广东佛山市付款后3天内
库存 10000桶起订10桶
品牌 多正化工
型号 828
规格 25KG
过期 长期有效
更新 2014-06-20 09:12
 
详细信息

Single-*ponent Water Based Spray Adhesive for Sponge HN-828

Introduction:This adhesive is water based, non-toxic and environmentally friendly.  It has long open time, fast drying speed, strong initial bonding strength, and it is heat resistant and anti-aging.

Besides, it can be used by single-side or double side spray method.

 

With the above features, it’s especially suitable for bonding sponge to sponge in making high-end soft furniture.  

 

 

 

Properties:

Appearance: Milky white liquid

Solid Content: 50±2%

Viscosity: 200-500cps25℃)

Working Condition: Temperature between 4-45, relative humidity under 80%

Bonding Time: Bond the material after 2~3 minutes

 

Transportation and Storage Temperature: 5-45

Odor: None

Strength: The biggest bonding strength is achieved after the glue cured 24 hours later

VOC: No volatilization

Quality Guarantee Period: 6 months

 

 

*pliance with Environmental Requirements

This adhesive contains no hazardous substance which has strict limit by the rule GB18583Limitation on Hazardous Substance in Adhesive for Interior Decoration Materials, and VOC is less than 50g/L, which *plies with the environmental requirements by ROHS and REACH.  This product has obtained the SGS certification.

 

 

Note:

1.      Avoid direct contact with eye.  Please wash with plenty water if the product is spattered into your eyes.

2.      Avoid exposure to the sun and frost while the product is in storage, transportation or application.  Tightly seal up the product after use to prevent surface crusting.

 

 

 

FAQ and Solution to Water Based Spray Adhesive:

FAQ

Possible Causes

Solution

Weak or no initial bonding strength

Slow evaporation on adhesive

Change the working process

Temperature is so low that initial bonding strength is affected.

Adjust the temperature in working field.

The adhesive layer is so thick that causes slow drying speed.

Adjust the spraying amount based on the correct operation.

The adhesive layer is so thin that causes shortage of gel.

Adjust the spraying amount based on the correct operation

Failure to spray

Low air pressure

Adjust the air pressure to normal state, 2.5-8kg.

Spray nozzle is stuck by gel

Clean out the gel from the nozzle by wet towel or finger.

Malfunction of spray gun

Change or fix the spray gun.

Uneven spraying

Low air pressure

Adjust the air pressure to normal state, 2.5-8kg.

Malfunction of spray gun

Change or fix the spray gun.

Spray distance is too far.

Adjust the spray distance and angle.

Adhesive viscosity is too high

Addpurified waterto adjust the viscosity.

Too misty when spraying

Spray distance is too far.

Adjust the spray distance and angle.

High air pressure.

Lower the air pressure

Too scattered when spraying

Adjust the sector-like spraying method to straight-line one.

No air evaporation equipment

Install air evaporation equipment to remove the unwanted mist.

defect of spray gun

Use spray gun with bigger nozzle.

Debonding with material partly stick together

 

 

Uneven spay causes pile-up of gel

Adjust the air pressure and distance of spray gun, and spray evenly.

Uneven spray causes shortage of gel

Adjust the air pressure and distance of spray gun, and spray evenly.

Bond without thoroughly drying (mainly occurs in winter and rainy season).

Bond the material after the adhesive surface dries. It takes 2~3 min. Use oven in wet weather.

Stress is not put on all parts of the material.

Stress on the material evenly.

Bond after the best bonding timing.

Bond the material within the best bonding time.

 

 

Clearance of Spray Gun

 

Pour out the adhesive from the spray can after use and use tap water to clean it.  Then fill in the can with water and spray it out to clean the absorption tube and the gun inner.  Alternatively, you can detach pneumatic tube, fill the absorption tube with water, and press the trigger to let the water flow out until the flowing water is as clean as the tap water. 

 

 

 

*parison of properties between Water Based Spray Adhesive and Solvent Based Spray Adhesive

Number

Item

Solvent Based Spray Adhesive

Water Based Spray Adhesive

1

Appearance

 

Light yellow or brown yellow

 

Milky white

2

Solid Content

30%  About 30%

50±2%

3

Spray area per kilogram of adhesive

 

About 7

 

About 20

4

Spray amount per 100

About 12KG

About 5KG

5

Spray ability

Large spray amount; double-side spray

Proper spray amount; double-side spray

6

Viscosity

SBS type:150cps

Cr type:400cps

 

200-500cps/25

7

Solvent

Organic solvent: benzene, ketones

Deionized water

8

VOC

>65%

0

9

Odor

Solvent odor

No Odor

10

Viscosity

Achieve the largest strength after 4 hours

Achieve the largest strength after 24 hours

11

Spray distance

50-80cm

20-40cm

12

Drying time

Edge-fold: 1min.

PVC leather: 1min

Thick leather: 2min-3min

Edge-fold:2min

PVC leather: 2min-3min

Thick leather: 2min-3min

13

Repeated bonding times

2-3 times

2-3 times and more if adhesive layer is thicker.

14

Bonding time

Within 30s after adhesive dries

Within 20-30s after adhesive dries

15

Specification of spray gun

F75, small spray gun PQ-2

Inquire the technician

16

 

Material’s movability after bonding (It can be turned to next process directly.) 

 

It can be turned to next process directly under normal circumstances.

 

It can be turned to next process directly under normal circumstances.

17

Heat resistance

 

50-60

 

80-90

18

Product Standards

GB-18583 2008 national certification

GB-19340 2003 SGS certification

19

Safety performance on fire-proof

 

Potential safety hazard caused by fire

 

Do not havepotential safety hazard caused by fire

 

 

单组份环保水性喷胶——海绵专用胶

 

 

水性喷胶型号:828

 

产品特性:本产品属高效水溶性胶粘剂,具有无毒不燃、绿色环保、开放时间长、干燥速度快、初粘性强、耐热性和防老化能力俱佳等优点。

产品用途:使用于海绵粘海绵的高档软体家具的制造,且可单面喷胶粘合。

水性喷胶产品参数:

外观:乳白色液体

 

 

固含量:50±2%

 

粘度:200-500cps25

 

 

施工条件:温度4-45℃,相对湿度低于80%

 

晾胶时间:2-3分钟以后贴合

 

 

运输和储藏温度:5-45℃

 

气味:无

强度:胶水固化24小时后拉力最大

VOC:挥发量为零

保质期:6个月

 

产品符合环保要求:

不含GB18583《室内装饰装修材料胶粘剂中有害物质限量》中有害物质,总挥发性有机物含量小于50g/L,符合欧洲ROHS和REACH环保标准,本产品已通过SGS的认证。

 

注意事项:

1、 避免该产品与眼睛直接接触,如不慎溅入眼睛,请马上用清水冲洗。

2、 产品在储存、运输和使用过程中需防止太阳暴晒和霜冻、胶水使用后应密封好包装桶,以防止胶水结皮而影响施工。